Find Us

Address
Km 15 West Service Road, South Super Highway, Barangay Sun Valley, Paranaque, 1700 Metro Manila

Hours
Monday—Friday: 9:00AM–5:00PM
Saturday & Sunday: 11:00AM–3:00PM

Search

Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

About This Site

This may be a good place to introduce yourself and your site or include some credits.

Filter by price

20AMP DC TO DC CHARGER WITH LITHIUM

₱ 30,000.00

  • Lithium (LiFePO4) Compatible
  • 25A Multi-Stage Battery Charger
  • Built-in Battery Isolator & MPPT Regulator
  • ETFO Charging Technology
  • Designed, engineered and tested in Australia

Quantity

Add to Wishlist
Add to Wishlist

Any Questions?

Check out overlandkings/faq
Or Shoot us a message at overlandkings/contact-us

Description

ADVENTURE KINGS 25AMP DC-DC CHARGER

MK2 LITHIUM COMPATIBLE (WITH MPPT SOLAR)

SOLAR PRIORITY DUAL-INPUT CHARGING

Can accept solar and alternator input (combined up to 25A output) at the same time for fast and efficicent charging and will prioritise solar over alternator to save fuel and reduce load on your engine.

THE BRAINS OF YOUR DUAL BATTERY SYSTEM

Isolates your batteries when your vehicle is off and properly charges from your alternator/starter battery while you’re driving. Designed for vehicles with or without smart alternators thanks to ignition sensing. The Kings DC-DC Charger is a multi-stage charger and battery isolator all in one! The updated Mk2 version builds on the success of the Adventure Kings Mk1 DC-DC charger and is ready to take your 12V dual battery system to the next level.

LITHIUM (LIFEPO4) CHARGE CAPABILITY

Specially programmed charge pattern specific to Lithium LiFePO4 batteries. Plus Kings DC-DC chargers can be set to charge most 12V lead acid batteries including wet/flooded, AGM Deep Cycle and Calcium Maintenance Free.

DESIGNED, TESTED AND ENGINEERED IN AUSTRALIA

We teamed up with a Brisbane-based Engineering and R+D company – Intelliquip Solutions so that every step of development was achieved in-house in Australia. That included writing over 10,000 lines of code, designing the unique circuit boards and housings, prototyping, component selection and all the laboratory and real world testing.

EXTREME TEMPERATURE, FULL OUTPUT (ETFO) CHARGING TECHNOLOGY

Adventure Kings DC-DC Chargers can output their stated 20Amps of charge even in constant, extremely hot ambient temperatures of up to 60°C* and internal temperatures around 90°C*. Reporting back to the charging chip there are two temperature sensors that monitor different parts of the circuit board and electronics to protect and regulate the unit for high efficiency and longevity – plus there’s an external battery-mounted temp sensor for highly accurate charge compensation.

INDUSTRIAL GRADE COMPONENTS

Industrial grade components from the USA and Japan are a step above commercial grade and are rated to suit higher working temperatures – plus we’ve innovated a new way to mount high-current wires to circuit boards for the ideal electrical connection and so it’s rugged enough to take on Australian off-road conditions.

BUILT TOUGH FOR AUSSIE CONDITIONS

A tough alloy housing means it is able to survive harsh conditions while being engineered with a built in heat sink for excellent passive cooling. It’s properly protected against reverse polarity, short circuiting, under/over voltage, over current as well as over temperature and battery under/over temperature.

 

 

 

Max. Charging Current 25A
Solar Input Working Voltage Range (25A DC-DC/MPPT model)  9 – 19V
Min. Input start-up Voltage – Solar (25A DC-DC/MPPT model)  14.5V
Ideal 12V Nominal Solar Panel Size (25A DC-DC/MPPT model) Voc <22V  360W
Vehicle Input Working Voltage Range  11.9 – 16V
Min. Input start-up Voltage – Vehicle  12.2V
Vehicle Input Working Voltage Range (Ign wire NOT fitted)  12.8 – 16V
Min. Input start-up Voltage – Vehicle (Ign Wire NOT fitted)  13.8V
Min. Aux Battery Voltage  5V
Idle Current Draw  20-30mA
Operation Temperature – Aux Battery  -10°C – 50°C
Dimensions  142 x 125.6 x 33.5mm
Weight  ~750g
Temperature Compensation  Yes
Temperature Sensor(s): Yes , two internal, one external with ring terminal for accurate battery temperature
Housing: Powder coated aluminium
LED Indicator lights: Yes – for status, connections and errors
Battery Chemistry Selection: Yes – Lithium (LiFePO4) AGM, wet lead acid/gel, calcium
Fuses required: Yes – not supplied (50A suggested)
Recommended wire size: Up to 8m – 6 AWG.     8-15m – 4 AWG

Reviews

There are no reviews yet.

Be the first to review “20AMP DC TO DC CHARGER WITH LITHIUM”

Product Video